MinkaAire F612 Specifications

CERTIFICATEHigh Sierra

4 HANGING THE FANWARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety

Fig. 10REGISTRATIONSLOTFig. 8DOWNRODSUPPLYWIRESFig. 7CROSS PINHANGERBALLDOWNRODSET SCREWFig. 6HITCHPINLOCKPINSET SCREWSFig. 5OUTLET BOXHANGER BRACKET

5ELECTRICAL CONNECTIONS WARNING:To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box

Step 3.Receiver to House Supply Wires Electrical connections:Connect the WHITE wire(Neutral) from the outlet box to the WHITE wire marked”AC in N” fro

Fig. 13WHITE (NEUTRAL)WHITE (NEUTRAL)GREEN OR BARECOPPER (GROUND)WHITE ( AC IN N )" "WHITE ( TO MOTOR N )" "GROUND-(GREEN)(CONNEC

6 FINISHING THE INSTALLATION″Step 1. Tuck connections neatly into ceiling outlet box.Step 2. Remove one screw from the hanger bracket and loosen the

7BLADE INSTALLATIONStep 1.Attach the fan blade to the blade holder using the screws and paper washers provided. Tighten screws securely. Repeat proces

8INSTALLING THE LIGHT KIT PLATEStep1.Remove 1of 4screws from the mounting ring and loosen the other 3 screws.(Do not remove.) Step2.Place the key hol

9INSTALLING THE LIGHT KIT ASSEMBLYLight Kit Warranty“This Ceiling fan Light Kit Fixture is covered by a Limited 2 year Warranty from the Manufacturer,

INSTALLING THE GLASS SHADE & LIGHT BULBS WARNING:Shut of the power supply before removing or replacing lamp. If you accidentally come i

Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.

11OPERATING THE REMOTE CONTROL/WALLTRANSMITTERRestore Power to Ceiling Fan.A. Buttons:These buttons are used to set the fan speeds as follows;= Low Sp

speed settings for warm or cold weather depend on factors such as room size, ceiling height and number of fans.NOTE : Wait for fan to stop before

4.There is no need to oil your fan. The motor has permanently lubricated bearings.5.If your fan is provided with glass shades, clean with lukewarm soa

SYMPTOM Fan will not startSOLUTION Check to make sure the wall switch is turned on. Check circult fuses or breakers. Caution! Make sure

SYMPTOMFan WobbleSOLUTION NOTE:All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even t

SYMPTOMFrequency InterferenceSOLUTION1.Turn the power off to your ceiling fan.2.Please use a small size tool to change the frequency settings on the c

SPECIFICATIONSThese are typical readings. Your actual fan may vary.They do not include amps and wattage used by the light (s). RFor any additional inf

xxx.xxxxx.xxxx.xxxxxx.xxxxxx.xxxxxx.xxxx.xxxx.xxxx.xx

R Minka-Aire warrants to the original owner that this fan will be free from defects in material and workmanship for one year R from the date of

This warranty shall not apply to fans which have been damaged in any way, including improper installation, damage as result of the removalof the f

CONTENTS INSTALLING THE LIGHT KIT PLATE 8INSTALLING THE LIGHT KIT ASSEMBLY

SAFETY RULES1 1. 2. Be cautious!Read all instuctions and safety information before installing your new fan. Review accompanying assembly di

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occ

PACKAGE CONTENTSUnpack your fan and check the contents.You should have the following items:2BA1591011121413823 45 671 1. Fan blades(5) 2. H ang

3INSTALLING THE FANMOUNTING OPTIONSIf there isn't an existing mounting box, then read the following instructions. Disconnect the power by removin